Diamond Wireless Repeater Installation
What are you trying to do with the repeater? The repeater should only function to locally increase your wireless signal, it does not provide DHCP addressing or act as a gateway. Consult your manual, but basically the repeater should have an ip address assigned that is within your network range, but not one that will be assigned by the DHCP server in your gateway router. For example if your gateway is 192.168.0.1, allow the DHCP to assign 192.168.0.2 to 198.168.0.50 and assign the repeater a static address of 192.168.0.51.
You may be trying to make a wired connection to the repeater to set it up, if so, the computer you connect will have to be in the same network as the default repeater address, so give your computer a temporary static address of 10.0.10.253 while connected to the repeater. Then when you type in the repeater address into IE you will get the configuration page. The bottom line is that for devices to work on the same network, they must have addressed in the same network range (or be bridged, which you don't need). What are you trying to do with the repeater?
The WR300NR has the wireless speed and range to power a complex set of networking applications creating a highly efficient mobile office or entertainment network. Main Features. Complies with IEEE 802.11n, IEEE 802.11g, IEEE 802.11b standards; Supports Router, Client, Bridge, Repeater, AP mode; QoS function. We’ve got a product review this week! Diamond’s WR300N is a super-compact wireless repeater/bridge device. Does it hold its own, or fall short of conventional.
The repeater should only function to locally increase your wireless signal, it does not provide DHCP addressing or act as a gateway. Consult your manual, but basically the repeater should have an ip address assigned that is within your network range, but not one that will be assigned by the DHCP server in your gateway router. For example if your gateway is 192.168.0.1, allow the DHCP to assign 192.168.0.2 to 198.168.0.50 and assign the repeater a static address of 192.168.0.51.
You may be trying to make a wired connection to the repeater to set it up, if so, the computer you connect will have to be in the same network as the default repeater address, so give your computer a temporary static address of 10.0.10.253 while connected to the repeater. Then when you type in the repeater address into IE you will get the configuration page. The bottom line is that for devices to work on the same network, they must have addressed in the same network range (or be bridged, which you don't need).
Thanks, tried setting a static ip as Download Anime Mitsudomoe Season 1 Sub Indo. 10.0.10.253 and 255. No luck, although I was not sure what to use for a default gateway. The Diamond quckstart guide made it so very easy.just disable wifi, attach the cable and enter 10.0.10.254. Doesn't say anything about network address ranges. I had te same problem!
But, after I awited 3-4 minutes, the sign-in screan came up and after I signed in as 'admin', I was able to run the setup. To find the repeater, you need to manually assign an IP address in your IPv4 settings. So get to the properties of your wireless network, double click on Internet Protocol Version 4, and choose 'Use the following IP address' instead of 'Obtain an IP address automatically', then enter the following: 10.0.10.1 for the IP address 255.255.255.0 for the Subnet Mask 10.0.10.254 for the Default gateway Click ok and try to access the repeater again on 10.0.10.254 at the browser. It should work now.
What if the repeater was already configured to another network and you change internet providers and want to reconfigure? I can't figure this out. To find the repeater, you need to manually assign an IP address in your IPv4 settings.
So get to the properties of your wireless network, double click on Internet Protocol Version 4, and choose 'Use the following IP address' instead of 'Obtain an IP address automatically', then enter the following: 10.0.10.1 for the IP address 255.255.255.0 for the Subnet Mask 10.0.10.254 for the Default gateway Click ok and try to access the repeater again on 10.0.10.254 at the browser. It should work now.